No products were found matching your selection.
Other Related Products
-
- Material: PE film with removable adhesive
- Color: Black/white, transparent, blue, or printed
- Thickness: Typical 60-100 um
- Adhesion: 1.8-5.5 N/25 mm typical range
- Roll format: Slit rolls for sheet lamination
- Suitable surface: Stainless steel, coated metal, aluminum sheet
-
Protective film for painted sheet goods should be selected around the full processing route, not from film thickness or initial tack alone. Pre-painted steel, coated aluminum, PCM/VCM panels, roofing sheet, cladding and other finished metal can be exposed to scratches, trapped particles, edge lifting, wrinkles, adhesive transfer and visible surface marking during slitting, punching, bending, roll forming, stamping, storage and shipment. A reliable approval plan starts with the actual coating and finish, then checks application conditions, deformation severity, dwell time and removal stage. Sample testing and a production-representative trial are recommended before full use.
-
- Material:Red transparent PET film or red transparent PVC film
- Color Density:Light red, standard red, deep red, or sample-matched tone
- Thickness:PET 25 um – 250 um / PVC 100 um – 500 um typical
- Light Transmission:Light red 55% – 78% / deep red 18% – 45% typical
- Surface:Smooth roll surface for printing, lamination, slitting, or die-cutting
- Uses:Packaging window, lighting filter, display overlay, LED window, visual identification
-
Polyester film water absorption is the percentage mass increase of a PET specimen after controlled water exposure. This TDS covers bare, treated, coated, and adhesive-backed PET constructions. Interpret results with thickness, conditioning, water temperature, exposure duration, and construction. Reference data can screen materials, but confirm the actual grade and finished structure by representative testing.
-
- Material: PE surface protection film
- Adhesive: acrylic-based or rubber-based
- Color options: clear, blue, black/white, custom print
- Thickness range: 30–120 microns
- Roll width: up to 3200 mm
- Surface fit: gloss, matte, satin, and lightly textured coatings
-
Laser cutting stainless steel with film is most reliable when the protective layer, stainless steel finish, lamination method, laser process, part geometry, and removal timing are validated as one system. This guide addresses bubbling at pierce points, lifting along cut paths, film shrinkage, surface contamination, scratches, adhesive transfer, and difficult removal on 2B, BA, mirror, brushed, hairline, and coated stainless steel. It is intended for sheet-metal processing where the film remains on the plate during cutting and may continue through bending, stacking, storage, or transport. The main acceptance test is a production-representative trial on the actual surface, machine, and removal schedule.
-
- Thickness: 250um / 0.25mm for rigid support parts
- Material: PET polyester film with insulating properties
- Color Options: Clear, translucent, milky white, black or custom color
- Surface: Smooth, flat surface with low-curl control
- Processing: Slitting, sheeting, punching, cutting and die-cutting
- Main Uses: Insulation gasket, spacer layer, washer and panel backing
-
- Material: PE film
- Adhesive: removable self-adhesive coating
- Common Colors: blue, clear, printed
- Common Widths: 24 in, 36 in, 48 in, 600 mm
- Common Roll Lengths: 200 ft, 500 ft, custom
- Typical Use: temporary protection for sealed hard floors
-
- Thickness: 100um / 0.1mm / approx. 4 mil
- Material: PET polyester film roll
- Color: Clear standard, other finishes on request
- Surface: Untreated, one-side corona, or two-side corona
- Roll format: Custom width, length, 76mm or 152mm core ID, roll OD
- Uses: Die-cutting, insulation parts, labels, adhesive coating, lamination
