No products were found matching your selection.
Other Related Products
-
- Thickness: 250um / 0.25mm for rigid support parts
- Material: PET polyester film with insulating properties
- Color Options: Clear, translucent, milky white, black or custom color
- Surface: Smooth, flat surface with low-curl control
- Processing: Slitting, sheeting, punching, cutting and die-cutting
- Main Uses: Insulation gasket, spacer layer, washer and panel backing
-
- Material: printed self adhesive PVC film with release liner.
- Width: 600 mm, 900 mm, 1220 mm, or custom slit width.
- Length: 10 m, 25 m, 50 m, or project roll format.
- Finish: glossy, satin matte, or soft stone texture.
- Pattern: white grey, black gold, beige stone, or custom veining.
- Surface: dry, flat, sealed and non-porous counter surfaces.
-
- Material: PET film with double side silicone coating
- Typical Thickness: 25 um, 36 um, 50 um, 75 um, 100 um
- Color Options: Clear, milky white, blue, red, or matte finish
- Release Design: Equal release or differential release liner
- Common Width: 300-1600 mm, slit roll available
- Main Use: Tape, label stock, foam tape, and die-cut liner
-
- Material: PE protective film
- Thickness: 30 / 40 / 50 / 60 / 80 microns
- Colors: Clear, blue, black & white
- Adhesion: Low, medium, or high
- Roll Width: Custom slit widths available
- Surface Finish: 2B, BA, mirror, brushed, No.4, hairline
-
- Common widths: 500 mm-1500 mm rolls
- Color options: blue, white, clear, black
- Base material: flame-retardant PE film
- Surface type: smooth or anti-slip embossed
- Thickness range: 80-1000 um
- Main use: temporary site surface covering
-
- Material: Optical PET or flexible film structure
- Common thickness: 0.10 mm to 0.18 mm
- Color: Clear transparent
- Surface: Glossy, anti-scratch coating optional
- Adhesive: Silicone or pressure-sensitive adhesive
- Supply form: Roll, sheet, or die-cut pieces
-
Protective film for painted sheet goods should be selected around the full processing route, not from film thickness or initial tack alone. Pre-painted steel, coated aluminum, PCM/VCM panels, roofing sheet, cladding and other finished metal can be exposed to scratches, trapped particles, edge lifting, wrinkles, adhesive transfer and visible surface marking during slitting, punching, bending, roll forming, stamping, storage and shipment. A reliable approval plan starts with the actual coating and finish, then checks application conditions, deformation severity, dwell time and removal stage. Sample testing and a production-representative trial are recommended before full use.
-
Laser cutting stainless steel with film is most reliable when the protective layer, stainless steel finish, lamination method, laser process, part geometry, and removal timing are validated as one system. This guide addresses bubbling at pierce points, lifting along cut paths, film shrinkage, surface contamination, scratches, adhesive transfer, and difficult removal on 2B, BA, mirror, brushed, hairline, and coated stainless steel. It is intended for sheet-metal processing where the film remains on the plate during cutting and may continue through bending, stacking, storage, or transport. The main acceptance test is a production-representative trial on the actual surface, machine, and removal schedule.
-
- Common roll width: 300 mm, 600 mm, 1000 mm, 1220 mm, 1650 mm
- Film thickness: 40 um-100 um
- Color options: Clear, blue, white, black-white, or printed marks
- Material: PE film with controlled hand-tear perforation
- Tear-off interval: 300 mm, 500 mm, 600 mm, 1000 mm, or custom
- Main use: Fast temporary covering for floors, counters, doors, windows, and duct openings
